Configuring the floppy disks
You can create your emergency boot floppy disk set on a pair of
3.5-inch 1.44MB (135tpi, 18 sectors per track) floppies
or a single 3.5-inch 2.88MB (135tpi, 36 sectors per track)
You cannot use LS-120 disks as boot media.
However, you can create the emergency boot floppy disk set
on an LS-120 drive
using conventional floppy disk media.
To create an emergency boot floppy disk set:
Store your emergency boot floppy disk set
(or single boot/root floppy disk)
in a safe and secure place.
Make sure they are easily accessible; you will need them if
your system becomes corrupted and is no longer bootable.
Log in as root.
Use the Floppy Manager
located in the Filesystems directory
of the SCOadmin hierarchy, or enter this command:
At the main menu, enter 2 to create the emergency boot
floppy disk set.
When prompted, indicate the type of disk drive you are using.
Unless you have a 2.88MB drive, enter 2.
If you have more than one floppy disk drive, you are prompted for the
drive that you are using to create the floppy disk.
Enter either 0 (for the primary drive) or 1
(for the secondary drive).
When prompted for the type of filesystem, select
1 to create the root floppy disk. If you are
creating a single boot/root floppy disk, select 3.
When prompted, insert a blank floppy disk and press <Enter>.
When prompted to format the floppy disk:
If the floppy disk is already formatted, enter n.
The filesystem is then created immediately.
If the floppy disk is not formatted, enter y.
You see the track and head numbers count up as the floppy disk is formatted.
(If the /etc/default/format file contains the string
VERIFY=Y, the format is also verified.)
A filesystem is created on the floppy disk and system files are copied
over to a RAM disk for compression, including copying
/dev/cmos to /etc/cmos.root.
You can use this file to restore the CMOS settings later
as described in
When you see the message:
Do you want a shell escape to place extra files on the root filesystem? (y/n)
If you want to place additional files on the disk, enter y and
follow the instructions in
``Adding files to the root floppy disk''.
Otherwise enter n.
If you are creating a single boot/root floppy disk, skip to step 13.
Disk space on the emergency boot floppy disks is limited and only
critical utilities are loaded. Where possible, additional
utilities such as
are copied when space
The filesystem is checked using
and displays messages similar to the filesystem
check displayed at boot time.
You are notified when the the floppy disk is ready.
Remove the floppy disk from the drive, and label it
``root'' and include the machine name.
Write-protect the disk so that you do not accidentally
erase the information.
Press <Enter> to continue and you are returned to the
filesystem type menu. Enter 2 to create the
boot floppy disk.
You have two options for the boot floppy disk: a system-specific disk that
contains the same kernel that is currently on your system, or a
smaller ``generic'' kernel that has fewer drivers linked in. If your
current kernel is too large to fit on the disk, you will be warned
and you will have to select the generic disk.
Insert the floppy disk and respond to the prompts as you did for
inserting and formatting the root floppy disk.
The boot floppy disk is created and you
see messages as files are copied to the disk.
Then, the filesystem is checked using
When complete, be sure and label it as you did with the root disk.
Follow the procedure in the
``Testing your emergency boot floppy disk set''
section to verify that you can boot your system and
access backups using your boot and root floppy disks.
Adding files to the root floppy disk
Creating an emergency boot floppy disk set
© 2003 Caldera International, Inc. All rights reserved.
SCO OpenServer Release 5.0.7 -- 11 February 2003