DOC HOME SITE MAP MAN PAGES GNU INFO SEARCH PRINT BOOK
 

Name

mount.cifs — mount using the Common Internet File System (CIFS)

Synopsis

mount.cifs {service} {mount-point} [-o options]

DESCRIPTION

This tool is part of the samba(7) suite.

mount.cifs mounts a Linux CIFS filesystem. It is usually invoked indirectly by the mount(8) command when using the "-t cifs" option. This command only works in Linux, and the kernel must support the cifs filesystem. The CIFS protocol is the successor to the SMB protocol and is supported by most Windows servers and many other commercial servers and Network Attached Storage appliances as well as by the popular Open Source server Samba.

The mount.cifs utility attaches the UNC name (exported network resource) to the local directory mount-point. It is possible to set the mode for mount.cifs to setuid root to allow non-root users to mount shares to directories for which they have write permission.

Options to mount.cifs are specified as a comma-separated list of key=value pairs. It is possible to send options other than those listed here, assuming that the cifs filesystem kernel module (cifs.ko) supports them. Unrecognized cifs mount options passed to the cifs vfs kernel code will be logged to the kernel log.

mount.cifs causes the cifs vfs to launch a thread named cifsd. After mounting it keeps running until the mounted resource is unmounted (usually via the umount utility).

OPTIONS

user=arg

specifies the username to connect as. If this is not given, then the environment variable USER is used. This option can also take the form "user%password" or "workgroup/user" or "workgroup/user%password" to allow the password and workgroup to be specified as part of the username.

Note

The cifs vfs accepts the parameter user=, or for users familiar with smbfs it accepts the longer form of the parameter username=. Similarly the longer smbfs style parameter names may be accepted as synonyms for the shorter cifs parameters pass=,dom= and cred=.

password=arg

specifies the CIFS password. If this option is not given then the environment variable PASSWD is used. If the password is not specified directly or indirectly via an argument to mount mount.cifs will prompt for a password, unless the guest option is specified.

Note that a password which contains the delimiter character (i.e. a comma ',') will fail to be parsed correctly on the command line. However, the same password defined in the PASSWD environment variable or via a credentials file (see below) or entered at the password prompt will be read correctly.

credentials=filename

specifies a file that contains a username and/or password. The format of the file is:

		username=value
		password=value

This is preferred over having passwords in plaintext in a shared file, such as /etc/fstab. Be sure to protect any credentials file properly.

uid=arg

sets the uid that will own all files on the mounted filesystem. It may be specified as either a username or a numeric uid. This parameter is ignored when the target server supports the CIFS Unix extensions.

gid=arg

sets the gid that will own all files on the mounted filesystem. It may be specified as either a groupname or a numeric gid. This parameter is ignored when the target server supports the CIFS Unix extensions.

port=arg

sets the port number on the server to attempt to contact to negotiate CIFS support. If the CIFS server is not listening on this port or if it is not specified, the default ports will be tried i.e. port 445 is tried and if no response then port 139 is tried.

netbiosname=arg

When mounting to servers via port 139, specifies the RFC1001 source name to use to represent the client netbios machine name when doing the RFC1001 netbios session initialize.

file_mode=arg

If the server does not support the CIFS Unix extensions this overrides the default file mode.

dir_mode=arg

If the server does not support the CIFS Unix extensions this overrides the default mode for directories.

ip=arg

sets the destination host or IP address.

domain=arg

sets the domain (workgroup) of the user

guest

don't prompt for a password

iocharset

Charset used to convert local path names to and from Unicode. Unicode is used by default for network path names if the server supports it. If iocharset is not specified then the nls_default specified during the local client kernel build will be used. If server does not support Unicode, this parameter is unused.

ro

mount read-only

rw

mount read-write

setuids

If the CIFS Unix extensions are negotiated with the server the client will attempt to set the effective uid and gid of the local process on newly created files, directories, and devices (create, mkdir, mknod).

nosetuids

The client will not attempt to set the uid and gid on on newly created files, directories, and devices (create, mkdir, mknod) which will result in the server setting the uid and gid to the default (usually the server uid of the user who mounted the share). Letting the server (rather than the client) set the uid and gid is the default. This parameter has no effect if the CIFS Unix Extensions are not negotiated.

perm

Client does permission checks (vfs_permission check of uid and gid of the file against the mode and desired operation), Note that this is in addition to the normal ACL check on the target machine done by the server software. Client permission checking is enabled by default.

noperm

Client does not do permission checks. This can expose files on this mount to access by other users on the local client system. It is typically only needed when the server supports the CIFS Unix Extensions but the UIDs/GIDs on the client and server system do not match closely enough to allow access by the user doing the mount. Note that this does not affect the normal ACL check on the target machine done by the server software (of the server ACL against the user name provided at mount time).

directio

Do not do inode data caching on files opened on this mount. This precludes mmaping files on this mount. In some cases with fast networks and little or no caching benefits on the client (e.g. when the application is doing large sequential reads bigger than page size without rereading the same data) this can provide better performance than the default behavior which caches reads (readahead) and writes (writebehind) through the local Linux client pagecache if oplock (caching token) is granted and held. Note that direct allows write operations larger than page size to be sent to the server. On some kernels this requires the cifs.ko module to be built with the CIFS_EXPERIMENTAL configure option.

mapchars

Translate six of the seven reserved characters (not backslash, but including the colon, question mark, pipe, asterik, greater than and less than characters) to the remap range (above 0xF000), which also allows the CIFS client to recognize files created with such characters by Windows's POSIX emulation. This can also be useful when mounting to most versions of Samba (which also forbids creating and opening files whose names contain any of these seven characters). This has no effect if the server does not support Unicode on the wire.

nomapchars

Do not translate any of these seven characters (default)

intr

currently unimplemented

nointr

(default) currently unimplemented

hard

The program accessing a file on the cifs mounted file system will hang when the server crashes.

soft

(default) The program accessing a file on the cifs mounted file system will not hang when the server crashes and will return errors to the user application.

--verbose

Print additional debugging information for the mount. Note that this parameter must be specified before the -o. For example:

mount -t cifs //server/share /mnt --verbose -o user=username

noacl

Do not allow POSIX ACL operations even if server would support them.

The CIFS client can get and set POSIX ACLs (getfacl, setfacl) to Samba servers version 3.10 and later. Setting POSIX ACLs requires enabling both XATTR and then POSIX support in the CIFS configuration options when building the cifs module. POSIX ACL support can be disabled on a per mount basic by specifying "noacl" on mount.

serverino

Use inode numbers (unique persistent file identifiers) returned by the server instead of automatically generating temporary inode numbers on the client. Although server inode numbers make it easier to spot hardlinked files (as they will have the same inode numbers) and inode numbers may be persistent (which is userful for some sofware), the server does not guarantee that the inode numbers are unique if multiple server side mounts are exported under a single share (since inode numbers on the servers might not be unique if multiple filesystems are mounted under the same shared higher level directory). Note that not all servers support returning server inode numbers, although those that support the CIFS Unix Extensions, and Windows 2000 and later servers typically do support this (although not necessarily on every local server filesystem). Parameter has no effect if the server lacks support for returning inode numbers or equivalent.

noserverino

client generates inode numbers (rather than using the actual one from the server) by default.

nouser_xattr

(default) Do not allow getfattr/setfattr to get/set xattrs, even if server would support it otherwise.

rsize=arg

default network read size

wsize=arg

default network write size

ENVIRONMENT VARIABLES

The variable USER may contain the username of the person to be used to authenticate to the server. The variable can be used to set both username and password by using the format username%password.

The variable PASSWD may contain the password of the person using the client.

The variable PASSWD_FILE may contain the pathname of a file to read the password from. A single line of input is read and used as the password.

NOTES

This command may be used only by root, unless installed setuid, in which case the noeexec and nosuid mount flags are enabled.

CONFIGURATION

The primary mechanism for making configuration changes and for reading debug information for the cifs vfs is via the Linux /proc filesystem. In the directory /proc/fs/cifs are various configuration files and pseudo files which can display debug information. For more information see the kernel file fs/cifs/README.

BUGS

Mounting using the CIFS URL specification is currently not supported.

The credentials file does not handle usernames or passwords with leading space.

Note that the typical response to a bug report is a suggestion to try the latest version first. So please try doing that first, and always include which versions you use of relevant software when reporting bugs (minimum: mount.cifs (try mount.cifs -V), kernel (see /proc/version) and server type you are trying to contact.

VERSION

This man page is correct for version 1.34 of the cifs vfs filesystem (roughly Linux kernel 2.6.12).

SEE ALSO

Documentation/filesystems/cifs.txt and fs/cifs/README in the linux kernel source tree may contain additional options and information.

umount.cifs(8)

AUTHOR

Steve French

The syntax and manpage were loosely based on that of smbmount. It was converted to Docbook/XML by Jelmer Vernooij.

The maintainer of the Linux cifs vfs and the userspace tool mount.cifs is Steve French. The Linux CIFS Mailing list is the preferred place to ask questions regarding these programs.